temporary files. WARNING: Any existing files in this
           folder are deleted.

/ig - Allows Setup to run on some older Gateway and Micron computers with

      an early BIOS.

/ih - This switch causes Setup to run ScanDisk in the foreground.

/im - Causes setup to ignore the conventional memory check.

/iq - If you use the /is switch to bypass ScanDisk or ScanDisk fails,

      Setup checks your drive for cross-linked files. The /iq switch
      prevents Setup from doing this.

/is - This switch causes Setup not to run ScanDisk.

/it - This switch bypasses checking for the presence of "dirty" or

      "deadly" terminate-and-stay-resident programs (TSRs) that are known
      to cause problems with Windows Setup.

/p - This switch causes Setup to pass string(s) directly to Detection

     Manager (or Sysdetmg.dll). Setup does not interpret the content of
     the string. The string can contain one or more detection options.
     The /p switch is not used by itself. For more information on
     the /p switch, please see the "/p Detection Switch Option String
     Defined" section below.

/p Detection Switch Option String Defined

• The string can contain one or more detection switches separated by a semicolon (;). For example, if you want to use "/p f" and "/p i" you type "setup /p f;i" (without quotation marks).
• Some switches are simply On/Off switches. The absence of the switch implies Off; the presence of the switch turns it On. A minus sign (-) appended immediately after a switch turns it Off.
• Some switches take parameters in the form of =. If there is more than one parameter to a switch, the parameters are separated by a comma (,).
• There must not be any spaces in the detection option string.

Valid Detection Switches:

a - This switch enables safe detection. It tells each detection module

    to try safer detection methods. Safer detection methods may not
    detect devices correctly.
    The default during Setup is enabled. The default in other cases is
    disabled.
    Example: setup /p a

b - This switch enables Prompt Before mode. It prompts you before a

    detection module is called so that you can step through each
    detection module manually and decide if you want to skip it.
    The default is disabled.
    Example: setup /p b

c - This switch enables class detection. Class detection is a mechanism

    for finding hints for a certain class of devices. For example, adapter
    class detection looks for hints in the Config.sys and System.ini files
    for CD-ROM drivers. If it does not find any, Setup displays a CD-ROM
    check box asking if you have a CD-ROM drive.
    The default during Setup is enabled. The default when you use the
    Add New Hardware tool and docking/undocking detection is disabled.
    Example: setup /p c

c- - Setup /p c- disables safe class detection. For example, this switch

     tells Setup to always search on all network adapter cards, sound
     cards, and CD-ROM drives.
     Example: setup /p c-

d= - This switch detects the listed detection modules only, where

            is a detection module name or a device class name.
           Detection module names (such as DetectPIC and DetectAHA154x)
           are found in the Msdet.inf file. Device class names can be
           SCSIAdapter, net, and so on.
           Example: setup /p d=detectpic

e - This switch enables Setup mode detection.

    The default during Setup is enabled. The default in other cases is
    disabled.
    Example: setup /p e

f - This switch enables Clean Registry mode. It forces Detection to

    clean the root branch of the registry before starting. This switch
    is ignored when Setup is run in the Windows 95/98 graphical user
    interface (GUI).
    The default is disabled.
    Example: setup /p f

g= - This switch specifies the verbose level, where is 0 to 3.

        This switch controls how verbose the built-in progress bar is. At
        maximum level (3), it shows all the resources of the detected
        devices along with the progress bar. This switch can help to
        identify which detection module causes a certain problem. For
        example, if your mouse stops responding (hangs) during detection
        but the system continues, there is no way to determine from the
        log files which module hung the mouse. By turning this option on
        and constantly moving the mouse during Setup, you can determine
        which module is running when the mouse hangs.
        The default is disabled (0).
        Example: setup /p g=3

i - This switch tells Setup not to report the existence of a Plug and

    Play BIOS. It is useful on computers that have a Plug and Play BIOS
    that is not reported in the Machine.inf file
    Example: setup /p i

j - This switch tells Setup to undo the results of the "Setup /p i"

    switch. This switch should only be used after a computer that required
    "Setup /p i" has updated its Plug and Play BIOS.
    Example: setup /p j
    NOTE: In Windows 98, the "/p j" switch is required to enable ACPI
    support. Windows 98 maintains a BIOS list for ACPI computers, so as
    BIOS manufacturers create a new valid ACPI BIOS, this is the mechanism
    for causing Windows 98 to recognize it.

l= - This switch specifies the logging level for Detlog.txt, where

         is 0 to 3.
        The default is maximum logging (3).
        Example: setup /p l=0

m - This switch enables Mini-windows mode.

    This is enabled only when Setup is run under MS-DOS.
    Example: setup /p m

n - This switch enables No Recovery mode. This option can be used to

    turn off the Windows 95 Setup recovery mechanism (for example, this
    switch prevents the creation of the Detcrash.log file).
    The default is disabled.
    Example: setup /p n

o= - This switch specifies the trace output. The information

                  is written to the Tracelog.txt file in the current
                  directory.
                  This option is available only in the Debug version of
                  Sysdetmg.dll.
                  Example: setup /p o

p - This switch enables performance logging. It writes performance

    timing information to the DETLOG.TXT file.
    The default is disabled.
    Example: setup /p p

r - This switch enables Recovery mode. It causes Detection to use the

    Detcrash.log file, if found, for recovery. If this switch is not
    enabled, Detection ignores and deletes Detcrash.log even if it is
    found.
    This switch is used if Safe Recovery is selected during Setup,
    otherwise it is not used.
    Example: setup /p r

s= - This switch skips the listed detection modules or classes of

           detection modules, where  is a detection module name or a
           device class name.
           Detection module names (such as DetectPIC and DetectAHA154x)
           are in the Msdet.inf file. Device class names are SCSIAdapter,
           net, and so on.
           Example: setup /p s=detectpic

t= - This switch specifies the trace level, where is 0 to 9.

        The default is disabled (0).
        This option is available only in the Debug version of
        Sysdetmg.dll.
        Example: setup /p t=9

v - This switch enables Verify Only mode. Detection has two stages:

    1. Verify existing devices in the registry.
    2. Detect new devices.
    This switch tells Detection to perfor m only stage 1. This switch is
    used by the PCMCIA Wizard to verify legacy devices in the registry.
    The default is disabled.
    Example: setup /p v

x= - This switch excludes the listed resources from
detection, 
               where  is one of four possibilities:
                - io(xxx-yyy,xxx-yyy,...)
                - mem(xxxxx-yyyyy,xxxxx-yyyyy,...)
                - irq(x,y,z,...)
                - dma(x,y,z,...)
                This switch protects resources so that no detection
                modules can access them.
                Example: setup /p x=io(300-30f,240-24f)
 

Back To directory